期刊检索

  • 2024年第56卷
  • 2023年第55卷
  • 2022年第54卷
  • 2021年第53卷
  • 2020年第52卷
  • 2019年第51卷
  • 2018年第50卷
  • 2017年第49卷
  • 2016年第48卷
  • 2015年第47卷
  • 2014年第46卷
  • 2013年第45卷
  • 2012年第44卷
  • 2011年第43卷
  • 2010年第42卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 哈尔滨工业大学 主编 李隆球 国际刊号ISSN 0367-6234 国内刊号CN 23-1235/T

期刊网站二维码
微信公众号二维码
引用本文:陈静,闫澍旺,孙立强,郎瑞卿.不同直径匹配度封堵气囊的工作机理和试验验证[J].哈尔滨工业大学学报,2018,50(6):130.DOI:10.11918/j.issn.0367-6234.201708092
CHEN Jing,YAN Shuwang,SUN Liqiang,LANG Ruiqing.Working mechanism and model test of plugging airbags with different diameter matching under external pressure[J].Journal of Harbin Institute of Technology,2018,50(6):130.DOI:10.11918/j.issn.0367-6234.201708092
【打印本页】   【HTML】   【下载PDF全文】   查看/发表评论  下载PDF阅读器  关闭
过刊浏览    高级检索
本文已被:浏览 2167次   下载 1238 本文二维码信息
码上扫一扫!
分享到: 微信 更多
不同直径匹配度封堵气囊的工作机理和试验验证
陈静,闫澍旺,孙立强,郎瑞卿
(水利工程仿真与安全国家重点实验室(天津大学),天津 300072)
摘要:
为研究气囊作为临时性封堵装置在隧道工程中的应用情况,建立其受力分析模型,得到了气囊内压和形状随外压增长的变化规律,得到了两种失效模式和正常工作时需要满足的3个控制条件,特别是外压不能大于内压这一独特的控制条件.由于气囊直径与隧道匹配度的大小直接影响封堵效果,因此确定直径允许误差范围在工程设计中至关重要.分别采用直径大于、等于、小于隧道直径的3种气囊进行堵气和堵水的模型试验,得到不同直径匹配度的气囊在气压和水压作用下的变形规律、内外压关系及失效极限状态的控制条件.试验结果表明:直径适中的气囊匹配性最好,气囊的变形和失效模式完全符合理论公式;直径略偏大的气囊若不出现初始贯通的褶皱,其封堵效果和失效模式与直径适中的气囊类似;直径偏小的气囊,由于一部分内压用于抵消使其膨胀至贴紧隧道壁所产生的材料拉力,容易导致其摩阻力不足而在外压作用下产生整体滑动.据此提出了气囊制作误差允许范围上下限的标准,为气囊制作过程中的误差控制提供依据.
关键词:  隧道封堵  气囊匹配度  均布和梯形荷载  失效模式  模型试验
DOI:10.11918/j.issn.0367-6234.201708092
分类号:TU375.2
文献标识码:A
基金项目:国家自然科学青年基金(51709198)
Working mechanism and model test of plugging airbags with different diameter matching under external pressure
CHEN Jing,YAN Shuwang,SUN Liqiang,LANG Ruiqing
(State Key Laboratory of Hydraulic Engineering Simulation and Safety (Tianjin University), Tianjin 300072, China)
Abstract:
To study the application of airbags as a temporary plugging device in the tunnel engineering, the force analysis model was established to obtain the change law of the inner pressure and shape of the airbag as the external pressure increases. Two kinds of failure modes and three control conditions that need to be met during normal operation were obtained, in particular the unique control condition that the external pressure cannot be greater than the internal pressure. Since the matching degree between the airbag diameter and the tunnel directly affect the sealing effect, it is important to determine the allowable error range of the airbag diameter in the engineering design. Then the model tests were carried with three airbags with different matching degree. The deformation, internal and control conditions of the failure limit state were obtained. The results show that the airbag with the smallest deviation has the best sealability and the deformation and failure modes of the airbag are in good agreement with the theoretical formula. The airbag with a larger diameter has wrinkles, but the blocking effect and failure mode are similar to those with a moderate diameter. The smaller diameter of the airbag, due to a part of the internal pressure to offset the tension, has smaller maximum static friction resistance and it tends to slide under the external pressure. The allowable error of the airbag diameter is proposed, providing the basis for airbag manufacturing process.
Key words:  tunnel plugging  matching degree of airbags  uniform and trapezoidal pressure  failure modes  model test

友情链接LINKS