期刊检索

  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:刘文胜,蔡青山,马运柱,龙路平.增塑挤压成形钨基合金棒材溶剂-热二步脱脂工艺研究[J].材料科学与工艺,2012,20(4):7-12.DOI:10.11951/j.issn.1005-0299.20120402.
LIU Wen-sheng,CAI Qing-shan,MA Yun-zhu,LONG Lu-ping.Study on solvent-thermal two-step degreasing process of tungsten-based alloy rods by plasticizing extrusion molding[J].Materials Science and Technology,2012,20(4):7-12.DOI:10.11951/j.issn.1005-0299.20120402.
【打印本页】   【HTML】   【下载PDF全文】   查看/发表评论  下载PDF阅读器  关闭
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 2621次   下载 2197 本文二维码信息
码上扫一扫!
分享到: 微信 更多
增塑挤压成形钨基合金棒材溶剂-热二步脱脂工艺研究
刘文胜, 蔡青山, 马运柱, 龙路平
中南大学 粉末冶金国家重点实验室,长沙 410083
摘要:
大长径比钨基合金棒材制备的关键是成形、脱脂和后续的烧结控制.基于增塑挤压成形的研究,对Ф24 mm钨基合金挤压棒坯的快速无缺陷脱脂,即溶剂-热二步脱脂工艺进行了研究.结果表明:在溶剂脱脂温度为45 ℃,脱脂12 h后,Ф24 mm钨基合金棒材一次脱脂率达45%;在溶剂脱指过程中增加干燥阶段,脱脂率可达70%以上;在真空气氛下对脱脂棒材进行后续热脱脂,坯体保形性好,且在12 h内,脱脂可以全部完成.采用溶剂-热二步脱脂工艺可以实现Ф24 mm钨基合金挤压棒材的快速无缺陷脱脂.
关键词:  钨基合金  粉末挤压成形  挤压棒材  溶剂-热二步脱脂工艺
DOI:10.11951/j.issn.1005-0299.20120402
分类号:
基金项目:国家自然科学基金资助项目(50774098).
Study on solvent-thermal two-step degreasing process of tungsten-based alloy rods by plasticizing extrusion molding
LIU Wen-sheng, CAI Qing-shan, MA Yun-zhu, LONG Lu-ping
State Key Laboratory for Powder Metallurgy,Central South University,Changsha 410083,China
Abstract:
The keys of preparation of large aspect ratio tungsten-based alloy rods are forming,degreasing and subsequent sintering control.According to the research of powder extrusion molding(PEM),the fast and defect-free degreasing of Ф24 mm tungsten-based alloy rods,made by two-step degreasing process including solvent and thermal stages,were mainly investigated in this paper.The results showed that,the binder removal ratio was about 45 wt.% of Ф24 mm tungsten-based alloy rods when the solvent degreasing temperature was 45 ℃ and the holding time was 12 h.The binder removal ratio was above 70 wt.% by increasing the drying stage during solvent degreasing.The green maintained good shape during subsequent thermal degreasing in a vacuum atmosphere,and the binder removal completed within 12 h.The solvent-thermal two-step degreasing process could achieve a fast and defect-free degreasing of Ф24 mm tungsten-based alloy rods extruded.
Key words:  tungsten-based alloy  PEM  extruded rods  solvent-thermal two-step degreasing process

友情链接LINKS