期刊检索

  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:黄晓燕,倪文,王中杰,钱嘉伟,祝丽萍.铜尾矿制备无石灰加气混凝土的试验研究[J].材料科学与工艺,2012,20(1):11-15.DOI:10.11951/j.issn.1005-0299.20120103.
HUANG Xiao yan,NI Wen,WANG Zhong jie,QIAN Jia wei,ZHU Li ping.Experimental study on autoclaved aerated concrete made from coppertailings without using lime as calcareous materials[J].Materials Science and Technology,2012,20(1):11-15.DOI:10.11951/j.issn.1005-0299.20120103.
【打印本页】   【HTML】   【下载PDF全文】   查看/发表评论  下载PDF阅读器  关闭
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 2492次   下载 1718 本文二维码信息
码上扫一扫!
分享到: 微信 更多
铜尾矿制备无石灰加气混凝土的试验研究
黄晓燕, 倪文, 王中杰, 钱嘉伟, 祝丽萍
北京科技大学金属矿山高效开采与安全教育部重点实验室,北京100083
摘要:
为了在综合利用固体废弃物的同时减少煅烧石灰所带来的CO2排放,采用铜尾矿-矿渣-水泥熟料-风积砂原料体系制备压加气混凝土,以富钙、镁的铜尾矿和矿渣代替传统加气混凝土所需的石灰.具体研究了各原料组份对加气混凝土物理力学性能的影响,得到B06级铜尾矿加气混凝土的优化配合比为:铜尾矿、矿渣、风积砂、水泥熟料、石膏的质量分数分别为30%、35%、20%、10%、5%.所制备的B06级蒸压加气混凝土的绝干密度为610.2 kg·m-3,抗压强度为4.0 MPa,达到了《蒸压加气混凝土砌块》(GB 11968—2006 )规定的A3.5、B06级加气混凝土合格品的要求.物相分析显示,所制备的加气混凝土中主要结晶相是板状的托贝莫来石、硬石膏、残留的石英以及来自原始铜尾矿中的残留矿物.
关键词:  铜尾矿  加气混凝土  配合比  抗压强度
DOI:10.11951/j.issn.1005-0299.20120103
分类号:TU522. 3
基金项目:
Experimental study on autoclaved aerated concrete made from coppertailings without using lime as calcareous materials
HUANG Xiao yan, NI Wen, WANG Zhong jie, QIAN Jia wei, ZHU Li ping
State Key Laboratory of High-Efficient Mining and Safety of Metal Mines Ministry of Education, University science and technology Beijing,Beijing 10083,China
Abstract:
Copper tailings,blast furnace slag,eolian sand,a small amount of clinker and gypsum were used as raw materials to prepare autoclaved aerated concrete(AAC).Lime was substituted by Ca and Mg rich copper tailings and blast furnace slag to reduce the CO2 emission brought by limestone calcinations.This study focused on the effect of different component of raw materials on the physical and mechanical properties of AAC.The optimal proportion of major raw materials for a B06 grade AAC is as follows:copper tailings 30%,blast furnace slag 35%,eolian sand 20%,clinker 10% and gypsum 5%.The prepared AAC sample has bulk density of 610.2 kg·m-3 and compressive strength of 4.0 MPa,which can reach the requirements of A3.5,B06 level of AAC product regulated by “autoclaved aerated concrete block” GB 11968—2006.Microstructure analyses show that the main crystalline phases in the AAC sample are tobermorite,anhydrite,residual quartz and residual minerals from copper tailings.
Key words:  copper tailings  autoclaved aerated concrete  mixing proportion  compressive strength

友情链接LINKS