| 引用本文: | 黎文航,孙丹丹,杨峰,王加友,任彦胜.新型窄间隙MAG旋转电弧传感焊缝偏差提取算法[J].材料科学与工艺,2011,19(6):48-52.DOI:10.11951/j.issn.1005-0299.20110609. |
| LI Wen-hang,SUN Dan-dan,YANG Feng,WANG Jia-you,REN Yan-sheng.A new type of welding deviation extraction algorithm based on rotating arc sensor for narrow gap MAG welding[J].Materials Science and Technology,2011,19(6):48-52.DOI:10.11951/j.issn.1005-0299.20110609. |
|
| 摘要: |
| 针对旋转电弧窄间隙MAG焊多层单道焊时坡口变化平缓,传统电弧传感方法灵敏度下降的缺点,提出了1种新的电弧传感偏差提取算法.对通过实验获取的U形底对接坡口不同焊缝偏差下的电弧信号进行分析,得出偏差的大小和方向与1个旋转周期内电流极值的数目和分布有很好的对应性,并通过Matlab仿真进一步验证上述关系的合理性和可靠性.由此,提出了1种基于电流极值数目和分布的焊缝偏差提取算法.该算法仅与极值分布和大体位置有关,克服了坡口加工误差或坡口变化变缓所带来的不利影响. |
| 关键词: 焊缝跟踪算法 电弧传感 窄间隙旋转电弧焊 高效焊接 |
| DOI：10.11951/j.issn.1005-0299.20110609 |
| 分类号:TG403 |
| 基金项目:国家自然科学基金资助项目(51005107);江苏省自然科学基金资助项目(BK2011509);江苏省高校自然科学基金项目(09KJD460002);江苏省高校科研成果产业化推进工程项目资助(JHB06-24);江苏高校优势学科建设工程资助;江苏省"青蓝工程"科技创新团队项目;江苏省"六大人才高峰"项目资助 |
|
| A new type of welding deviation extraction algorithm based on rotating arc sensor for narrow gap MAG welding |
|
LI Wen-hang1, SUN Dan-dan2, YANG Feng2, WANG Jia-you2, REN Yan-sheng2
|
|
1.School of Material Science and Engineering,Jiangsu University of Science and Technology,Zhenjiang 212003,China2.Jiangsu Modern Shipbuilding Technology Co.,Ltd.,Zhenjiang 212003,China;2.School of Material Science and Engineering,Jiangsu University of Science and Technology,Zhenjiang 212003,China
|
| Abstract: |
| For multi-layer single pass welding of narrow gap rotating arc MAG welding,to overcome the sensitivity reducing problem of the traditional arc sensor seam as the groove changed slow,a new type of arc sensor welding deviation extraction algorithm was put forward.At first,the characters of welding current wave under different welding deviations of U-type groove butt welding were analyzed,and it showed that there were relations between the extreme values′ distribution and the welding deviation.Then,this relation′s rationality and reliability were verified by Matlab simulation and programming.Therefore,considering of the characteristics of welding and algorithm′s reliability,a welding seam tracking algorithm was put forward based on the number and distribution of welding current′s extreme.The algorithm only concerns with the extreme values′ distribution and can overcome the adverse effects of groove′s processing errors or soft change. |
| Key words: seam tracking algorithm arc sensor narrow gap MAG weld high effective welding |
