期刊检索

  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:申晓妮,任凤章,赵冬梅,肖发新.基于PCB的次磷酸钠化学镀铜研究[J].材料科学与工艺,2012,20(3):17-23.DOI:10.11951/j.issn.1005-0299.20120304.
SHEN Xiao-ni1,REN Feng-zhang,ZHAO Dong-mei,XIAO Fa-xin.Electroless copper plating on PCB using sodium hypophosphite as reducing agent[JZ[J].Materials Science and Technology,2012,20(3):17-23.DOI:10.11951/j.issn.1005-0299.20120304.
【打印本页】   【HTML】   【下载PDF全文】   查看/发表评论  下载PDF阅读器  关闭
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 2193次   下载 1597 本文二维码信息
码上扫一扫!
分享到: 微信 更多
基于PCB的次磷酸钠化学镀铜研究
申晓妮1,2, 任凤章1, 赵冬梅1, 肖发新1
1.河南科技大学 材料科学与工程学院,河南 洛阳 471003;2.河南省有色金属材料重点实验室,河南 洛阳 471003
摘要:
为解决传统甲醛化学镀铜体系环境污染及稳定性低的问题,以次磷酸钠化学镀铜体系为研究对象,采用SEM、XRD、电化学等测试方法,探讨了添加剂硫酸镍、α-α’联吡啶和马来酸对该体系的影响.结果表明:适量的硫酸镍和马来酸均能提高化学镀速并改善镀层外观质量,其适宜的质量浓度分别为0.8 g/L和10 mg/L;α–α’联吡啶能明显改善镀层外观质量,其适宜的质量浓度为10 mg/L;次磷酸钠体系的镀液稳定性能优越,加入混合添加剂在80 ℃下稳定时间近48 h;混合添加剂使化学镀铜阴极峰电流增大;在最佳工艺条件下镀速为5.10 μm/h,获得的镀层均匀、致密,施镀20 min后背光级数达到10级.
关键词:  添加剂  PCB  化学镀铜  硫酸镍  次磷酸钠
DOI:10.11951/j.issn.1005-0299.20120304
分类号:TQ153.14
基金项目:国家自然科学基金资助项目(50904023,50771042);河南省科技创新人才计划资助项目(104100510005);河南省基础与前沿技术研究计划资助项目(092300410064).
Electroless copper plating on PCB using sodium hypophosphite as reducing agent[JZ
SHEN Xiao-ni1,REN Feng-zhang,ZHAO Dong-mei,XIAO Fa-xin
Abstract:
The influences of additives (nickel sulfate,L–arginine,α–α’–dipyridyl and maleic acid )on sodium hypophosphite electroless copper plating were investigated using SEM ,XRD and electrochemical tests to solve the problem of pollution and low stability of formaldehyde electroless copper plating.The results show that the plating rate and coating quality are increased by proper amount of nickel sulfate and maleic acid,and the appropriate dosage are 0.8 g·L-1 and 10 mg·L-1,respectively,the coating quality is greatly improved by proper amount of α–α’–dipyridyl and the proper amount is 10 mg·L-1.The stability of sodium hypophosphite bath is excellent,and the stability time of bath with the addition of mixed additives reaches the highest of 48 h at 80 ℃.The cathode peak current density is also increased after mixed additives are added.The plating rate is 5.10 μm·h-1 and the coating is uniform and compact under optimal conditions,the backlight level achieves 10 grade after plating for 20 min.
Key words:  additive  PCB  electroless Cu plating  nickel sulfate  sodium hypophosphite

友情链接LINKS