期刊检索

  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:曹军,丁雨田,郭廷彪.铜线性能及键合参数对键合质量的影响[J].材料科学与工艺,2012,20(4):76-79.DOI:10.11951/j.issn.1005-0299.20120414.
CAO Jun,DING Yu-tian,GUO Ting-biao.Effect of copper properties and bonding parameters on bonding quality[J].Materials Science and Technology,2012,20(4):76-79.DOI:10.11951/j.issn.1005-0299.20120414.
【打印本页】   【HTML】   【下载PDF全文】   查看/发表评论  下载PDF阅读器  关闭
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 2180次   下载 2103 本文二维码信息
码上扫一扫!
分享到: 微信 更多
铜线性能及键合参数对键合质量的影响
曹军, 丁雨田, 郭廷彪
兰州理工大学 有色金属新材料国家重点实验室,兰州 730050
摘要:
为了提高铜线性能及其键合质量,采用拉力-剪切力测试仪、扫描电镜等研究了不同力学性能铜线及相应的键合参数对其键合质量的影响,分析了不同伸长率和拉断力、铜线表面缺陷、超声功率和键合压力对铜线键合质量的作用机制.结果表明:伸长率过小和拉断力过大会造成焊点颈部产生微裂纹,从而导致焊点的拉力和球剪切力偏低;表面存在缺陷的铜线其颈部经过反复塑性大变形会造成铜线表面晶粒和污染物脱落而出现短路和球颈部断裂;键合过程中键合压力过大能够引起的焊盘变形,同时较大的接触应力引起铝层溢出;过大的超声功率使键合区域变形严重产生明显的裂纹和引起键合附近区域严重的应力集中,致使器件使用过程中产生微裂纹而降低器件的使用寿命.
关键词:  伸长率  拉断力  表面  超声功率  键合压力
DOI:10.11951/j.issn.1005-0299.20120414
分类号:
基金项目:甘肃省科技攻关资助项目(2GSO64-A52-05).
Effect of copper properties and bonding parameters on bonding quality
CAO Jun, DING Yu-tian, GUO Ting-biao
State Key Laboratory of Gansu Advanced Non-ferrous Metal Materials,Lanzhou University of Technology, Lanzhou 730050,China
Abstract:
For improving the copper properties and bonding quality,the influence of different elongation,tensile strength,defects of copper surface,bonding power and bonding force on bonding quality is researched by pull strength-shear strength and scanning electron-microscopy(SEM).The results show that the small elongation and high tensile strength can cause micro-crack,and the bonding strength and shear strength are too low.The repeated large plastic deformation will cause copper surface chip and contamination falling and cause short circuit and crack.In bonding process,large bonding force can cause pad deformation,and high contact force can cause aluminum layer overflow.And the bonding area would deform and crack because of stress concentration caused by high bonding power,which would generate micro-crack in the using process and reduce the life of device.
Key words:  elongation  tensile strength  surface  bonding power  bonding force

友情链接LINKS