期刊检索

  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:彭俊阳,罗德高,滕步刚,刘钢.薄壁Y型三通管内高压成形起皱与开裂分析[J].材料科学与工艺,2017,25(4):11-16.DOI:10.11951/j.issn.1005-0299.20170061.
PENG Junyang,LUO Degao,TENG Bugang,LIU Gang.Analysis on wrinkling and cracking initiation in hydroforming thin-walled Y-shaped tubes[J].Materials Science and Technology,2017,25(4):11-16.DOI:10.11951/j.issn.1005-0299.20170061.
【打印本页】   【HTML】   【下载PDF全文】   查看/发表评论  下载PDF阅读器  关闭
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 2575次   下载 1404 本文二维码信息
码上扫一扫!
分享到: 微信 更多
薄壁Y型三通管内高压成形起皱与开裂分析
彭俊阳1,2,罗德高1,滕步刚1,刘钢1
(1.哈尔滨工业大学 材料科学与工程学院,哈尔滨 150001;2.中国商飞北京民用飞机技术研究中心 民用飞机结构与复合材料北京市重点实验室,北京 102211)
摘要:
本文针对薄壁Y型三通管在内高压成形过程中产生起皱、开裂缺陷的问题进行了相关研究.首先通过实验确定了Y型三通管在成形过程中产生典型缺陷的位置及类型;其次利用有限元方法分析了补料比对应力状态分区和典型点应力轨迹的影响;最后建立了加载路径的"内压-轴向补料"成形窗口.研究表明:补料比对应力状态有显著影响, 通过调整补料比来改变应力状态, 是避免起皱的有效措施.此外, 本研究给出了不同实验结果在成形窗口中的对应位置, 当加载路径超出成形区时, 三通管件就会产生起皱或破裂的缺陷, 甚至两种缺陷会依次发生.
关键词:  内高压成形  Y型三通管  起皱  开裂  补料量
DOI:10.11951/j.issn.1005-0299.20170061
分类号:TG306
文献标识码:A
基金项目:
Analysis on wrinkling and cracking initiation in hydroforming thin-walled Y-shaped tubes
PENG Junyang1,2, LUO Degao1, TENG Bugang1, LIU Gang1
(1.School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China; 2.Beijing Key Laboratory of Civil Aircraft Structures and Composite Materials, Beijing Aeronautical Science & Technology Research Institute of COMAC, Beijing 102211, China)
Abstract:
The wrinkling and bursting during thin-walled Y-shaped tube hydroforming process were studied. The location and type of typical defects were identified through experiments. The effects of feeding ratio on the stress states zone and the stress trajectory of typical points were analyzed by finite element method. The forming window of "internal pressure-axial feeding" was established to guide the loading paths. The results indicate that the feeding ratio can exert a crucial role on stress states. Fine adjusting feeding ratio can effectively avoid wrinkling. Meanwhile, the corresponding position of different experimental results in forming window was identified. Wrinkling or bursting would occur, and even these two defects would happen successively as the loading path exceeds the range of forming zone.
Key words:  hydroforming  Y-shaped tube  wrinkle  crack  feeding ratio

友情链接LINKS