期刊检索

  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:刘文胜,罗莉,马运柱,彭芬,黄国基.稀土Ce对SnAgCu合金显微组织及剪切强度的影响[J].材料科学与工艺,2012,20(6):115-120.DOI:10.11951/j.issn.1005-0299.20120621.
LIU Wen-sheng,LUO Li,MA Yun-zhu,PENG fen,HUANG Guo-ji.Effects of rare earth Ce on microstructure and shear properties of SnAgCu solder alloys[J].Materials Science and Technology,2012,20(6):115-120.DOI:10.11951/j.issn.1005-0299.20120621.
【打印本页】   【HTML】   【下载PDF全文】   查看/发表评论  下载PDF阅读器  关闭
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 1952次   下载 1243 本文二维码信息
码上扫一扫!
分享到: 微信 更多
稀土Ce对SnAgCu合金显微组织及剪切强度的影响
刘文胜, 罗莉, 马运柱, 彭芬, 黄国基
中南大学 粉末冶金国家重点实验室,长沙 410083
摘要:
研究了稀土Ce对Sn-3.0Ag-0.5Cu合金显微组织及焊点剪切强度的影响规律.利用扫描电镜对铸态合金及焊点显微组织和断口形貌进行了观察和分析,利用能谱仪对铸态合金组分进行测试,采用力学试验机测试焊点的剪切强度.研究表明:当Ce添加量为0.25%时,铸态合金显微组织中β-Sn 相与Ag3Sn相明显细化,出现了少量的Sn-Ce相及Ce的偏聚区;采用气雾化粉末所配制的焊膏进行回流焊,添加Ce后,焊点基体组织比未添加时明显优化;经过气雾化制粉,Ce向粉末表面富集并极易氧化,导致焊粉氧含量升高,使得回流焊接后焊料/Cu界面IMC层附近孔洞增加,焊点剪切强度降低.
关键词:  SnAgCu焊料  稀土Ce  显微组织  剪切强度  气雾化
DOI:10.11951/j.issn.1005-0299.20120621
分类号:
基金项目:国家配套项目( JPPT-115-2-1057).
Effects of rare earth Ce on microstructure and shear properties of SnAgCu solder alloys
LIU Wen-sheng, LUO Li, MA Yun-zhu, PENG fen, HUANG Guo-ji
State Key Laboratory for Powder Metallurgy,Central South University,Changsha 410083,China
Abstract:
The effects of rare earth Ce on the microstructure and shear properties of SnAgCu solder were investigated in this paper.The microstructure and fracture morphologies were measured by SEM,the components of alloy were analyzed by EDS,and the mechanical properties of solder joints were tested by mechanical test enginery.The results show that,when the 0.25wt.% Ce was added,the β-Sn phase and Ag3Sn phase in the microstructure were refined,and small amounts of Sn-Ce phases and partial gathering areas of Ce were observed;After reflowing with the solder paste prepared from gas-atomized powder,the microstructure of solder joints matrix was refined with Ce addition.The oxygen contents of solder powders increased because Ce was tend to surface enrichment and oxidation after gas-atomization,and the holes near the IMC layer were increased after reflowing,so the shear strength of solder joints decreased.
Key words:  SnAgCu solder  rare earth Ce  microstructure  shear properties  gas-atomization

友情链接LINKS