期刊检索

  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:王国建,孙耀宁,蒋万乐,张丹丹,杨杰.紫外线对玻纤环氧乙烯基酯树脂基复合材料性能的影响[J].材料科学与工艺,2017,25(3):46-51.DOI:10.11951/j.issn.1005-0299.20160249.
WANG Guojian,SUN Yaoning,JIANG Wanle,ZHANG Dandan,YANG Jie.Effects of UV on the properties of glass epoxy vinyl resin-based composites[J].Materials Science and Technology,2017,25(3):46-51.DOI:10.11951/j.issn.1005-0299.20160249.
【打印本页】   【HTML】   【下载PDF全文】   查看/发表评论  下载PDF阅读器  关闭
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 1579次   下载 1300 本文二维码信息
码上扫一扫!
分享到: 微信 更多
紫外线对玻纤环氧乙烯基酯树脂基复合材料性能的影响
王国建,孙耀宁,蒋万乐,张丹丹,杨杰
(新疆大学 机械工程学院,乌鲁木齐 830047)
摘要:
对玻璃纤维增强环氧乙烯基酯树脂基复合材料在温湿环境下进行了人工紫外加速老化实验,并进行了拉伸、弯曲等试验,分析了试件紫外老化后的质量损失率、巴氏硬度、弯曲破坏形态以及力学性能的演变规律, 并利用SEM观察了试样表面老化前后的形貌变化.研究表明:紫外线照射后试样的表面泛黄,且随照射时间的延长颜色不断加深;试样拉伸和弯曲性能以及巴氏硬度在紫外老化前期有所上升,160 h后开始下降;质量损失率随着紫外光照射时间的延长而逐渐增大;紫外老化后试件的弯曲破坏过程与未老化试件一致;随着老化周期的增加,孔隙量和韧性发白光带数量增加,呈现出明显的片层状海浪花样.
关键词:  纤维增强复合材料  紫外老化  拉伸性能  弯曲性能  巴氏硬度  SEM
DOI:10.11951/j.issn.1005-0299.20160249
分类号:TB332
文献标识码:A
基金项目:国家自然科学基金资助项目(51465055);新疆维吾尔族自治区自然科学基金资助项目(2014211A010);国家重点实验室开放课题资助项目(Sklms2014005).
Effects of UV on the properties of glass epoxy vinyl resin-based composites
WANG Guojian,SUN Yaoning,JIANG Wanle,ZHANG Dandan,YANG Jie
(Department of Mechanical Engineering, Xinjiang University,Wulumuqi 830047,China)
Abstract:
Artificial UV accelerated aging test in this artificial environment with certain temperature and humidity was done with glass fiber reinforced epoxy vinyl ester resin composite, and then the tensile and bending test were also done with the extension of UV irradiation time. The evolvement rules of mass loss rate, Barcol rigidity, flexural failure structure, mechanical property after aging were analyzed, and the morphological changes of the samples were observed by SEM. The results showed that the sample surface was turning yellow, and darkedn with time; the tensile and bending properties and Barcol rigidity were upward at the early stage of UV exposure, and then declined after 160 h. The failure pattern of tensile and bending after aging is consistent with those of the unaged samples.The mass lose rate of material declined with the time of UV exposure. SEM images showed that with the increase of the aging time, cavity density and tenacity white stripe with was increasing, which also is the obvious slice layer of wave pattern.
Key words:  fiber reinforced polymer  UV aging  tensile property  bending property  barcol hardness  SEM

友情链接LINKS