期刊检索

  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:郭占英,刘拥军,方海鹏.热处理对GH4169激光焊接头组织性能的影响[J].材料科学与工艺,2020,28(2):60-66.DOI:10.11951/j.issn.1005-0299.20180357.
GUO Zhanying,LIU Yongjun,FANG Haipeng.Effect of heat treatment on microstructure and properties of GH4169 laser welded joint[J].Materials Science and Technology,2020,28(2):60-66.DOI:10.11951/j.issn.1005-0299.20180357.
【打印本页】   【HTML】   【下载PDF全文】   查看/发表评论  下载PDF阅读器  关闭
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 598次   下载 516 本文二维码信息
码上扫一扫!
分享到: 微信 更多
热处理对GH4169激光焊接头组织性能的影响
郭占英,刘拥军,方海鹏
(西南交通大学 材料科学与工程学院,成都 610031)
摘要:
针对2 mm厚的GH4169镍基合金板材进行激光对焊,研究热处理对GH4169激光焊接头组织和性能的影响。采用线切割方法制备激光焊接头试样,对热处理和非热处理激光焊接头进行拉伸实验、硬度测定、OM分析、SEM分析、EDS分析和XRD相分析。实验结果表明:热处理后接头抗拉强度为1 372 MPa,延伸率为14%,焊缝平均硬度为473HV;较未热处理接头强度提高52%,延伸率降低71%,硬度提高69%。OM、SEM、EDS和XRD分析表明:对GH4169激光焊接头热处理能细化焊缝晶粒,改善枝晶形态,消除残余应力,析出δ相、γ′相和γ″相,使得焊接接头硬度和强度有所提高。
关键词:  GH4169  激光焊  显微组织  热处理  力学性能
DOI:10.11951/j.issn.1005-0299.20180357
分类号:TG407
文献标识码:A
基金项目:中央高校基本科研业务费专项资金资助项目(WK2090050018).
Effect of heat treatment on microstructure and properties of GH4169 laser welded joint
GUO Zhanying, LIU Yongjun, FANG Haipeng
(School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031, China)
Abstract:
Laser butt welding was carried out on 2 mm-thick plates of GH4169 superalloy. Welded joint samples were cut by Wire Electrical Discharge Machining (WEDM). Half of the welded joint samples were standard heat treated and the others were not, and the hardness and tensile properties of the welded joints were evaluated. Results show that the tensile strength of the welded joints after heat treatment was 1 372 MPa, the elongation was 14%, and the average weld hardness was 473 HV. Compared with non-heat treated welded joints, the tensile strength of the heat treated welded joints increased by 52%, elongation reduced by 71%, and hardness increased by 69%. OM, SEM,EDS, and XRD analyses show that heat treatment refined the laser welded joint grain, improved the dendrite morphology, eliminated the residual stress, and especially precipitated δ phase, γ′phase and γ″ phase, which improved the hardness and strength of the welded joints.
Key words:  GH4169  laser welding  microstructure  heat treatment  mechanical properties

友情链接LINKS