| 引用本文: | 邢佶慧,史一剑,吴超,杨庆山.建筑用热轧奥氏体304不锈钢管力学性能[J].哈尔滨工业大学学报,2014,46(2):78.DOI:10.11918/j.issn.0367-6234.2014.02.015 |
| XING Jihui,SHI Yijian,WU Chao,YANG Qingshan.Mechanics properties of hot rolled seamless Austenitic 304 stainless steel pipe[J].Journal of Harbin Institute of Technology,2014,46(2):78.DOI:10.11918/j.issn.0367-6234.2014.02.015 |
|
| 摘要: |
| 为了解热轧无缝不锈钢管材料性能,分别对取材自奥氏体304 Φ216×16 mm热轧不锈钢管的光滑和缺口圆棒试件进行单调和循环加载两类试验,获取了应力-应变关系及基本材料参数,得到滞回和骨架曲线,标定钢材循环强化参数,并观察了断面微观破坏特征．研究表明:国产热轧不锈钢管加工工艺对中厚管材性影响不大;奥氏体304不锈钢在循环荷载作用下具有良好强化效应和耗能性能;宜采用随动-等向混合强化材料模型描述其行为,所标定循环强化参数可用于复杂应力状态下的数值模拟;不锈钢材微观破坏特征异于普通低合金或低碳钢． |
| 关键词: 热轧钢管 单向拉伸 循环荷载 材料参数 微观破坏特征 |
| DOI：10.11918/j.issn.0367-6234.2014.02.015 |
| 分类号: |
| 基金项目:国家自然科学基金资助项目(51278036);中国铁路总公司科技研发计划项目(2013T002-A-2);中央高校基本科研业务费专项资金资助项目(2010JBZ011)． |
|
| Mechanics properties of hot rolled seamless Austenitic 304 stainless steel pipe |
|
XING Jihui, SHI Yijian, WU Chao, YANG Qingshan
|
|
(School of Civil Engineering, Beijing Jiaotong University, 100044 Beijing,China)
|
| Abstract: |
| To study the material behaviors of hot-rolled circle hollow austenitic 304 stainless steel members applied widely in large-span roofs, both smooth and notched round specimens were cut from Φ216×16 mm tubes and tested under monotonic tensile and cyclic axial loadings. Stress-strain curves were obtained to determine basic material parameters as well as load-displacement hysteretic responses and skeleton curves. In addition, fracture micromorphology of the specimens was observed. It is shown that the properties of middle thick austenitic 304 stainless steel are not significantly influenced by hot-rolled forming process. The stainless steel exhibits extensive strain-hardening and higher energy dissipation capabilities under cyclic loadings. As a result, kinematic-isotropic composite hardening material model should be adopted to simulate nonlinear response of this material. Cyclic hardening material parameters are calibrated by test results and used well in the numerical simulations.However, the fracture micromorphology characteristic of the stainless steel is quite different from that of low alloy or carbon steel. |
| Key words: hot rolled circle hollow section member monotonic tension cyclic loading material parameter fracture micromorphology characteristic |
