| 引用本文: | 徐加秋,阳恩慧,李奥,黄兵,李世佳,邱延峻.沥青胶结料低温临界开裂温度计算的改进方法[J].哈尔滨工业大学学报,2020,52(9):92.DOI:10.11918/201906069 |
| XU Jiaqiu,YANG Enhui,LI Ao,HUANG Bing,LI Shijia,QIU Yanjun.Improved method for calculating low temperature critical cracking temperature of asphalt binder[J].Journal of Harbin Institute of Technology,2020,52(9):92.DOI:10.11918/201906069 |
|
| |
|
|
| 本文已被：浏览 1166次 下载 1192次 |
码上扫一扫！ |
|
|
| 沥青胶结料低温临界开裂温度计算的改进方法 |
|
徐加秋1,3,阳恩慧,1,3,李奥1,3,黄兵2,李世佳2,邱延峻1,3
|
|
(1.西南交通大学 土木工程学院,成都 610031;2. 四川藏区高速公路有限责任公司,成都 610000; 3.道路工程四川省重点实验室,成都610031)
|
|
| 摘要: |
| 针对当前沥青胶结料温度应力和低温临界开裂温度计算方法的局限性,为找寻一种更好的沥青胶结料温度应力及相应的低温临界开裂温度计算方法,选取4种不同产地的70#基质沥青进行旋转薄膜老化（RTFO）和压力箱老化（PAV）展开研究. 利用BBR试验获得沥青胶结料的蠕变柔量,分别采用Hopkins & Hamming算法和CAM模型两步计算法以及Laplace变换一步计算法获得了沥青的温度应力,基于SAP理论计算相应的低温临界开裂温度. 通过统计学方法对计算结果进行比较和分析,采用相关性分析并结合实测路表温度数据对计算方法予以验证. 结果表明:Laplace变换一步计算法和Hopkins & Hamming算法两步计算法具有良好一致性,基于t检验法的低温临界开裂温度p值计算结果达0.90以上. Laplace变换一步计算法与BBR试验具有较强的相关性,临界开裂温度TCR与S/m指标、Huet流变模型指标的相关系数分别可达0.84、0.94. 实测路表温度变化数据的计算结果证明了该方法不仅适用于匀速降温工况,也适用于任意降温速率下的现场连续变速降温工况. |
| 关键词: 道路工程 沥青胶结料 临界开裂温度 弯曲梁流变试验 温度应力 低温性能 |
| DOI：10.11918/201906069 |
| 分类号:U414 |
| 文献标识码:A |
| 基金项目:国家自然科学基金(51778541) |
|
| Improved method for calculating low temperature critical cracking temperature of asphalt binder |
|
XU Jiaqiu1,3,YANG Enhui1,3,LI Ao1,3,HUANG Bing2,LI Shijia2,QIU Yanjun1,3
|
|
(1. School of Civil Engineering, Southwest Jiaotong University, Chengdu 610031, China; 2. Sichuan Tibet Expressway Co., Ltd., Chengdu 610000, China; 3. Key Laboratory of Highway Engineering of Sichuan Province, Chengdu 610031, China)
|
| Abstract: |
| In view of the limitations of the current calculation methods for thermal stress and low temperature critical cracking temperature of asphalt binder and in order to find a better method for calculating thermal stress and corresponding low temperature critical cracking temperature of asphalt binder, the 70# matrix asphalt of four different origins was selected for rotating thin film oven (RTFO) and pressure aging vessel (PAV) tests. The creep compliance of the asphalt binder was obtained by BBR test. The thermal stress of the asphalt were obtained by two-step calculation method of Hopkins & Hamming algorithm and CAM model as well as one-step calculation method of Laplace transform respectively, and the corresponding low temperature critical cracking temperature was calculated based on SAP theory. Calculation results were compared and analyzed by statistical methods. The calculation methods were verified by correlation analysis and combined with measured road surface temperature data. Results show that the one-step calculation method of Laplace transform and the two-step calculation method of Hopkins & Hamming algorithm were in good agreement. The calculation result of p-value of low temperature critical cracking temperature based on t-test was more than 0.90. The Laplace transform one-step calculation method had a strong correlation with the BBR test. The correlation coefficients between the critical cracking temperature TCR and the S/m index as well as the Huet rheological model index reached 0.84 and 0.94, respectively. The calculation results of the measured road surface temperature change data prove that the proposed method is not only suitable for uniform cooling conditions, but also for on-site continuous variable speed cooling conditions at any cooling rate. |
| Key words: road engineering asphalt binder critical cracking temperature bending beam rheological test thermal stress low temperature performance |
|
|
|
|
